DD-WRT Wi-fi Router Bridge Linksys 160N and WRT54GS

On this easy methods to information I will probably be exhibiting you ways create a wi-fi bridge between a Linksys 160n wi-fi router and a Linksys WRT54GS wireless router that has been modded with the DD-WRT firmware. You may ask your self what's a wireless bridge.You additionally could ask your self why you'd need to create a wi-fi bridge in the first place. Well a wi-fi bridge is once you connect one router to a different router without using any hard wired cables. Chances are you'll want to create a wi-fi bridge for a number of the following reasons.

Pc are situated at totally different ends of your house and you cannot run a ethernet cable between the two router. You want to link to you neighbors community so you may share web service, files, and media comparable to music and movies. The possibilities are endless with regards to networking routers together using wireless.

For the wireless bridge setup I will be using the following ip deal with and subnet setup:

* Wi-fi Router 1 = Linksys WRT160n 192.168.1.0/24
* Wi-fi Router 2 = Linksys WRT54GS-WRT mod 10.0.1.0/24

The Linksys WRT 160n wi-fi router will be immediately related to the Internet service, and the Linksys WRT54GS DD-WRT modded router will create the wi-fi hyperlink between the two routers. One of the best ways to setup your wireless bridge is to have a pc that has both a wifi connection and a ethernet connection. To start the set up, use your wireless connection to hook up with router 1, which is the Linksys WRT160N. After you've linked the router, open your web browser and type in the default gateway which needs to be 192.168.1.1. Click on the Standing Tab and guantee that router 1 has a web connection.

After you realize that the first router has a web connection, go to the Wireless Security Tab and setup the encryption sort and paraphrase key. Just remember to are using compatible encryption between both of the routers.linksys-wrt160n-wpa-wi-fi-safety

After you've got set the encryption type and key on the primary router, disconnect from this router. Now connect with the WRT54GS DD-WRT modded router, then go to the setup tab and change the local community to 10.0.1.0 or no matter community vary you prefer.

* Local Ip Address: 10.0.1.1
* Subnet Mask: 255.255.255.0
* Gateway: 10.0.1.1
* Local Dns: 10.0.1.1

After you will have changed the community setup in your modded DD-WRT router, disconnect from the router then reconnect to so that you just obtain your new ip address. Your new ip address needs to be someplace inside the 10.0.1.0 network. Now open an internet browser at level it in direction of 10.0.1.1, which is now the default gateway in your WRT54GS DD-WRT modded router.

Now go to the standing tab and click on on the wi-fi tab. Within the wireless tab it's best to see a button that claims site survey. The site survey button is located in the direction of the underside of the page. All you must do now is choose router 1 from the record, which should be the Linksys WRT160N.

After you may have selected router 1 from the checklist, go to the wireless tab and click on on the wi-fi safety tab. All it's a must to do now is enter the very same encryption sort and key that you setup for router 1. After you will have set the encryption kind and key into ybur modded DD-WRT router, all you have to do is apply the settings. It is best to now have a wireless link between the Linksys WRT160N and the Linksys WRT54GS. Now join utilizing a wireless connection to the DD-WRT modded router, and ensure your web connection work.

Article Source: http://www.newsarticlessite.com

DD-WRT Wireless Router Bridge Linksys 160N and WRT54GS

Please Rate this Article

5 out of 54 out of 53 out of 52 out of 51 out of 5 

Not yet Rated